General Description
Type:
Air Drying F-Class Epoxy Varnish
Description:
- The flexible nature of this product in a cured film provides Insulating protection while allowing for heat expansion & contraction. Electro Red Insulating Varnish is highly resistant to oils, moisture & temperature fluctuations. The cured coating is rated at 2500 volts/mil. Dries to touch in 10 minutes & dries to handle in 45 minutes.
- Electro Spray Air Drying F-Class Epoxy Varnish, single Compound
- The cured material displays very good Film formation & resistance to chemicals
- Owing to its temperature index 180-200 can be used for motor internal Class-F
Special Properties
- Flexible will not crack / age. Ideal for motors exposed to voltage / amperage fluctuations, frequent start-stop…
- Class F air drying single component
- Penetrates, strongly adheres. Does not drip / run out. Ideal for “In-situ” insulation applications. Simply open motor & covers & spray on.
- Versatile can be used on motors, bus bars, insulators...
- Excellent for “In-situ” motor insulation & “IR” value up gradation.
- Smooth, glossy, pin hole free di-electric coating.
- Excellent resistance to alkalies, acids, opens air weathering.
Characteristics & Properties:
| No. | Description | Results |
| 1 | Color Appearance | Red Color |
| Gloss at 60˚ >90 | ||
| Class Gloss | ||
| 2 | Class of Insulation | F Class |
| 3 | Chemical Base | Epoxy |
| 4 | Coverage | Theoretical – at1 mil dry 20 sq. ft./can |
| Practical – at1/2 mil dry 40 sq. ft./can | ||
| 5 | Drying Schedule: (At 77˚F (25˚C), 50% Humidity at 1 mil,dry) | |
| Surface Dry | 10 Min | |
| Tack Free | 30 Min | |
| Hard Dry | 8 Hours | |
| 6 | Weight per gallon | 7.56 lbs |
| 7 | Specific Gravity | 0.91 |
| 8 | Viscosity | Not Applicable |
| 9 | Flammability: Label marking | Extremely flammable |
| 10 | Flash point | <0˚F (18˚C) |
| 11 | Operating temperature range | 50˚ to 90˚ F (10˚ to 32˚C) |
| 12 | Percent solids by weight | 13% |
| 13 | Percent solids by volume | 11% |
| 14 | Percent pigment by volume | 0.30% |
| 15 | Volatile Organic Compound level | CARB VOC & MIR Exempt |
| 16 | Interior durability | Excellent |
| 17 | Exterior durability | Not Applicable |
| 18 | Temperature resistance | Class F |
| 19 | Color fastness | Excellent |
| 20 | Adhesion | Excellent |
| 21 | Salt spray corrosion | NA |
| 22 | Mineral spirits resistance | Very Good |
| 23 | Gasoline resistance | Poor |
| 24 | Motor oil resistance | Excellent |
| 25 | Pencil hardness | B |
| 26 | Food contact rating | Not Applicable |
| 27 | Dielectric strength | 2100 Volts / xylene |
| 28 | Resin system | Epoxy ester |
| 29 | Solvents (top two) | Trichlorethylene / xylene |
| 30 | Propellant system | Di-methyl ether |
Characteristics & Properties:
Remove all loose dirt, dust, grease, wax & rust particles from surface to be coated. Pre clean using #901 Easyclean (NF) for beast results, applies at temperatures between 60˚ to 80 ˚F (16˚ & 27˚C). Apply 3-4 light coats instead of one heavy coat. Shake can vigorously for one minutes. Hold can12 to 14 inched from surface. The darkness of the color indicates the thickness of the coating. To prevent clogging, turn can upside down & spray for approximately three seconds to clear varnish in valve.
Uses:
Improves “IR Values” of both new & old / rewound electric motor.
Use Aeroe’s Crown Insulating Varnish to protect electrical leads, coat frayed insulation & to restore dielectric properties lost from friction wear. Additional uses are to insulate & seal out moisture from armature windings, high voltage circuits, communicator ends & coils. Highly recommended for coating electrical windings that are exposed to moisture / voltage & amperage fluctuations repeatedly.
Shipping, Storage & Health:
| IMDG number | 1950 |
| D.O.T. container spec | 2P |
| D.O.T. Shipping description | Consumer commodity |
| Warehouse storage level number | NFPA 30B level 1 |
| Hazardous class (CFR-49) | ORM-D |
| Storage temperature | 32˚ to 120˚F (0˚ to 49˚C) |
| Shelf Lif | 1-2 Year |
| HMIS ratings | |
| Health | 2 |
| Fire | 4 |
| Reactivity | 0 |
Important:
1. Contains no Ozone Depleting Substances (O.D.S.).
2. Warranted to confirm to international ICC & DOT regulations.
3. Minimum 12 months performance guarantee –Warranted against ay defect in material or workmanship for a
period of 12 months from the date of supply.
4. Minimum 12 months zero wastage guarantee- 100% reliable aerosol spraying action & full contents spray-out
guaranteed for a period of 12 months from the date of supply.
